OWNER’S MANUALBEDIENUNGSANLEITUNG
DIGITAL SYSTEM AMPLIFIER10 Owner‘s Manual2.7 Selecting the Mode of Output (OUTPUT)Different output modes are available for the amplifier‘s output c
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 1170 V ModeThe 70 V mode allows connection of 70 V loudspeaker lines (Direct Drive) in high impedance mode (
DIGITAL SYSTEM AMPLIFIER12 Owner‘s Manualnot affected by VLD. Power amplifier channels behave as described in chapter 2.7. The use of VLD considera
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 132.10 Audio CablingInputInputs are electronically balanced. Whenever possible, using balanced audio signal
DIGITAL SYSTEM AMPLIFIER14 Owner‘s Manual3 Operation3.1 Volume ControlIn DUAL and PARALLEL mode, the level controls LEVEL on the power amp’s rear
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 154 OptionsInstalling one of the optionally available extension modules in the extension slot on the rear p
DIGITAL SYSTEM AMPLIFIER16 Owner‘s ManualControls and Connections1 INIT buttonThe INIT button allows resetting the RCM-810 to factory settings. P
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 173 STATUS LEDThe STATUS LED is for monitoring the communication on the CAN bus. The LED blinks rhythmical
DIGITAL SYSTEM AMPLIFIER18 BedienungsanleitungINHALTEinführung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bedienungsanleitung 19WICHTIGE SICHERHEITSHINWEISE1. Lesen Sie diese Hinweise.2. Heben Sie diese Hinweise auf.3. Beachten Sie alle Warnungen.4. Ric
DIGITAL SYSTEM AMPLIFIER2 CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIGITAL SYSTEM AMPLIFIER20 Bedienungsanleitung1 EinführungMit den Endstufen der DSA-Serie von Dynacord beginnt ein neues Zeitalter in der Endstufe
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 212 Installation2.1 Bedienelemente, Anzeigen und AnschlüsseFrontseiteRückseite1 Pegelanzeige für Kanäl
DIGITAL SYSTEM AMPLIFIER22 Bedienungsanleitung2.2 BetriebsspannungDie Spannungsversorgung der Endstufe erfolgt über die Netzeingangsbuchse. Trennen
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 23Geräterückseite nicht behindert wird. Für den Einbau in Gehäuse und Racksist zu beachten, dass eine a
DIGITAL SYSTEM AMPLIFIER24 BedienungsanleitungPARALLELIn der Betriebsart PARALLEL sind die Eingänge der Kanäle A und B direkt elektrisch verbunden
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 252.7 Wahl des Ausgangs-Modus (OUTPUT)Die Endstufenkanäle der Endstufen DSA 8405/8410/8805 können auf v
DIGITAL SYSTEM AMPLIFIER26 Bedienungsanleitung70 V-ModusDer 70 V Modus erlaubt den direkten Antrieb (Direct Drive) von 70 V Lautsprecherlinien im H
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 27und 100 V verhalten sich unverändert wie in Kapitel 2.7 beschrieben. Durch die Verwendung von VLD erw
DIGITAL SYSTEM AMPLIFIER28 Bedienungsanleitung2.10 Audio VerkabelungEingangDie Phoenix-Eingänge INPUT sind elektronisch symmetrisch ausgelegt. Wenn
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 293 Betrieb3.1 Eingangspegel-ReglerIn den Betriebsarten DUAL und PARALLEL regeln die Eingangspegel-Reg
Owner‘s Manual 3IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.
DIGITAL SYSTEM AMPLIFIER30 Bedienungsanleitung4 OptionenDurch den Einbau eines optionalen Zusatzmoduls in den Erweiterungssteckplatz an der Rückse
DIGITAL SYSTEM AMPLIFIERBedienungsanleitung 311 INIT-TasteDie INIT-Taste erlaubt das Rücksetzen des RCM-810 auf die Werkseinstellungen. Betätigen
DIGITAL SYSTEM AMPLIFIER32 Bedienungsanleitung4 REMOTE CAN BUS-AnschlüsseDas RCM-810-Modul besitzt zwei RJ-45-Buchsen für den REMOTE CAN BUS. Die
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual / Bedienungsanleitung 33Specifications/Technische DatenDSA 8405Amplifier at rated conditions, all channels d
DIGITAL SYSTEM AMPLIFIER34 Owner‘s Manual / BedienungsanleitungDSA 8410Amplifier at rated conditions, all channels driven, rated loads, unless othe
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual / Bedienungsanleitung 35DSA 8805Amplifier at rated conditions, all channels driven, rated loads, unless othe
DIGITAL SYSTEM AMPLIFIER36 Owner‘s Manual / Bedienungsanleitung5.1 Mains Operation & Resulting TemperatureDSA 8405 Output ModeUmains in VImains
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual / Bedienungsanleitung 371) Sine Modulation (1 kHz)2) Pink Noise EN60065 / 7. Edition3) 1 BTU = 1055.06 J = 1
DIGITAL SYSTEM AMPLIFIER38 Owner‘s Manual / BedienungsanleitungBlock Diagram / Blockschaltbild
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual / Bedienungsanleitung 395.2 Dimensions / Abmessungen
DIGITAL SYSTEM AMPLIFIER4 Owner‘s Manual1 IntroductionDynacord‘s new high efficiency DIGITAL SYSTEM AMPLIFIER series combine uncompromising audio
DIGITAL SYSTEM AMPLIFIERSubject to change withou prior notice. Printed in Germany Rev 3
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 5that interference will not occur in a particular installation. If this equipment does cause harmful interfe
DIGITAL SYSTEM AMPLIFIER6 Owner‘s Manual2 Installation2.1 Controls, Indicators and ConnectionsFront ViewRear View1 Level Indicators for each chann
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 72.2 Operating VoltageThe power amplifier receives its power supply via the mains input. During installation
DIGITAL SYSTEM AMPLIFIER8 Owner‘s Manualventilation. Since temperatures inside of the cabinet/rack case can easily riseup to 40 °C during operation
DIGITAL SYSTEM AMPLIFIEROwner‘s Manual 9PARALLELIn PARALLEL mode, the inputs of channel A and channel B are directly electrically linked. The audio
Kommentare zu diesen Handbüchern